Recent Content by KingScumbag

  1. KingScumbag
    Post

    Hellcat Fuel pump basket

    Isn't that going to crush/kink that supply when it compresses down into the tank? It compresses a way when installed.
    Post by: KingScumbag, Mar 22, 2020 in forum: Mazdaspeed 3/6 Hard Parts Fabrication
  2. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    Lilupdate. I own a business now ‍♂️ www.dirtywaterracing.com Been slowly transitioning shedbuilt name and parts over to this. My cousin and I...
    Post by: KingScumbag, Feb 25, 2020 in forum: Mazdaspeed 3 Build Diaries
  3. KingScumbag
    Post

    Eric’s 10 Speed 3 build

    We were sitting at over 650hp on my car. The pump was barely sneezing. We were limited by the wastegate so we never ended up journeying any...
    Post by: KingScumbag, Feb 25, 2020 in forum: Mazdaspeed 3 Build Diaries
  4. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    I have 3 blocks torn down at the moment. Building one for a customer, Sleeving one for the next build in my car (going to be a while new build)...
    Post by: KingScumbag, Nov 17, 2019 in forum: Mazdaspeed 3 Build Diaries
  5. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    No idea. Chalking it up to just straight up engine block failure and stress. The steel sleeves just separated from the casting on the deck of the...
    Post by: KingScumbag, Nov 16, 2019 in forum: Mazdaspeed 3 Build Diaries
  6. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    Slowest time of the top 10 in the world so you wouldn't be wrong in that statement :infodeskperson:
    Post by: KingScumbag, Nov 16, 2019 in forum: Mazdaspeed 3 Build Diaries
  7. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    Thread update? I've gone 10.5 @ 135 Aaaand popped the motor after getting some 5.9s in the car. Didn't even get to make a pas with them. Big...
    Post by: KingScumbag, Nov 15, 2019 in forum: Mazdaspeed 3 Build Diaries
  8. KingScumbag
    Post

    Cas' 800+ or Bust Build

    For 450 pump mod I make sure they are running an external FPR. The way i run and the way j recommend is splitting the feed to the HPFP and PI this...
    Post by: KingScumbag, Nov 14, 2019 in forum: Mazdaspeed 3 Build Diaries
  9. KingScumbag
    Post

    Post S3 install thread because KiwiFail

    And den
    Post by: KingScumbag, Sep 26, 2019 in forum: Mazdaspeed 3 Build Diaries
  10. KingScumbag
    Post

    Built Engine BNR S5 build

    Correct I am running the Kelford 65lb springs
    Post by: KingScumbag, Sep 23, 2019 in forum: Mazdaspeed 3 Build Diaries
  11. KingScumbag
    Post

    Post S3 install thread because KiwiFail

    :elefant:
    Post by: KingScumbag, Sep 23, 2019 in forum: Mazdaspeed 3 Build Diaries
  12. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    Yea the ghetto vice grip roller wasn't cutting it for the big boost. This thing was 130$ in Amazon. Worked great. Also some videos of the pass
    Post by: KingScumbag, Jun 26, 2019 in forum: Mazdaspeed 3 Build Diaries
  13. KingScumbag
    Post

    Shedbuilt and Scumbuilt

    Nope, no experience in drag racing. YEARS ago I had a couple passes in a built FoxBody I had but that's it. Before I started this drag racing...
    Post by: KingScumbag, Jun 26, 2019 in forum: Mazdaspeed 3 Build Diaries