Recent Content by Malevolous

  1. Malevolous
    Post

    Scarlet's Story

    Last steps are getting the headlights and front end on, fixing a fuel leak on these PTFE lines, figuring out why the drivers taillamp isn't...
    Post by: Malevolous, Feb 20, 2024 in forum: Mazdaspeed 6 Build Diaries
  2. Malevolous
    Post

    Scarlet's Story

    Finally starting to look like a car again. Thought I'd drop some progress pics to put down in the books. Before:
    Post by: Malevolous, Feb 20, 2024 in forum: Mazdaspeed 6 Build Diaries
  3. Malevolous
    Post

    Scarlet's Story

    Thanks for the info! Late reply, but I'm finally up to this phase. Is this done by just shoving a hose into the bottom port of the EGR and T'ing...
    Post by: Malevolous, Feb 20, 2024 in forum: Mazdaspeed 6 Build Diaries
  4. Malevolous
    Post

    Scarlet's Story

    I was planning on Versatune for that reason, but the issue I only discovered a couple days ago is that it removes the CEL from the dash, but the...
    Post by: Malevolous, Aug 18, 2023 in forum: Mazdaspeed 6 Build Diaries
  5. Malevolous
    Post

    Scarlet's Story

    I'm reading it's M18 x 1.5 thread. @Erebus that helped shed some anxiety, thanks for that lol Having a hard time finding any online. Seems even...
    Post by: Malevolous, Aug 17, 2023 in forum: Mazdaspeed 6 Build Diaries
  6. Malevolous
    Post

    Scarlet's Story

    Awesome news! And thanks for the info. Can confirm I see no O2 sensors, bungs, or disconnected connectors on/near the downpipe. Makes sense how it...
    Post by: Malevolous, Aug 16, 2023 in forum: Mazdaspeed 6 Build Diaries
  7. Malevolous
    Post

    Scarlet's Story

    So after speaking with Eric, the plan will be to clip the VTCS pigtail from my old harness (probably crimp new terminals onto new wires) and...
    Post by: Malevolous, Aug 16, 2023 in forum: Mazdaspeed 6 Build Diaries
  8. Malevolous
    Post

    Scarlet's Story

    Good to know, thanks for saving me the money and more importantly, time! I had the harness done by the main man himself, Eric. I'll check with him...
    Post by: Malevolous, Aug 15, 2023 in forum: Mazdaspeed 6 Build Diaries
  9. Malevolous
    Post

    Scarlet's Story

    Thanks for the tip, I'll try to source one somewhere. I'm sure I already know the answer to this, but if my Mazdaspeed Wire Tuck set was requested...
    Post by: Malevolous, Aug 15, 2023 in forum: Mazdaspeed 6 Build Diaries
  10. Malevolous
    Post

    Scarlet's Story

    Finally figured out the clutch wire splice dilemma. I found a cut W/L wire that was tucked under the fusebox, so that whole portion is resoldered...
    Post by: Malevolous, Aug 15, 2023 in forum: Mazdaspeed 6 Build Diaries
  11. Malevolous
    Post

    Possible Throttle Issue

    Didn't forget about you. Still going at it. I will say I found a lot of potential vac leaks and bad or damaged gaskets. My issues could be due to...
    Post by: Malevolous, Aug 14, 2023 in forum: Mazdaspeed 3 Troubleshooting
  12. Malevolous
    Post

    Scarlet's Story

    Haven't posted an update in a long time - a lot has happened lol. The clutch wire BS will be reverted back to stock. High up, under the...
    Post by: Malevolous, Aug 7, 2023 in forum: Mazdaspeed 6 Build Diaries
  13. Malevolous
    Post

    Possible Throttle Issue

    I wish, still replacing and upgrading parts lol. My current situation:[IMG] Sent from my SM-N986U using Tapatalk
    Post by: Malevolous, May 1, 2023 in forum: Mazdaspeed 3 Troubleshooting
  14. Malevolous
    Post

    Scarlet's Story

    Small update: got a replacement SSC on the way so I'm planning to start unsplicing this one from my harness. When tracing all the open/loose wires...
    Post by: Malevolous, Mar 18, 2023 in forum: Mazdaspeed 6 Build Diaries
  15. Malevolous
    Post

    Scarlet's Story

    This just keeps getting better...[IMG] Sent from my SM-N986U using Tapatalk
    Post by: Malevolous, Mar 16, 2023 in forum: Mazdaspeed 6 Build Diaries