Recent Content by Ssinstaller

  1. Ssinstaller
    Post

    Is there a difference between the MS3 and CX7 Longblocks?

    I have a cx7 longblock in my ms6. There were no issues with the swap.
    Post by: Ssinstaller, Mar 14, 2022 in forum: MZR Knowledgebase
  2. Ssinstaller
    Post

    Big Engine Oil loss

    The oil feed for the turbo bolts to the block right in that area. It's a banjo bolt, could be slightly loose or have bad crush washers.
    Post by: Ssinstaller, Nov 23, 2020 in forum: Mazdaspeed 3 Troubleshooting
  3. Ssinstaller
    Post

    relocating ecu help

    The ecm case is grounded. There are no issues other than noise/vibration if it touches the chassy.
    Post by: Ssinstaller, Nov 23, 2020 in forum: Mazdaspeed 3 General Discussion
  4. Ssinstaller
    Post

    Fuel pump resistor

    Fuse would blow before you damaged the resistor.
    Post by: Ssinstaller, Nov 23, 2020 in forum: Mazdaspeed 6 Troubleshooting
  5. Ssinstaller
    Post

    Low level output from amp

    Terminals b7-B10 can be used for your rca connections, b11 should be fine for remote.
    Post by: Ssinstaller, Sep 17, 2020 in forum: Mazdaspeed 3/6 Audio & Electronics
  6. Ssinstaller
    Post

    Low level output from amp

    Oem radio has a 2v differential output. You can wire channels one and two at the oem amp directly to an rca for your aftermarket amp.
    Post by: Ssinstaller, Sep 16, 2020 in forum: Mazdaspeed 3/6 Audio & Electronics
  7. Ssinstaller
    Post

    let`s take control of the SWAS

    https://catalog.pac-audio.com/catalog/specialty-items/tr7 Wire and program for option 12. You turn on the ignition, it'll output a negative...
    Post by: Ssinstaller, Sep 13, 2020 in forum: Mazdaspeed 3 General Discussion
  8. Ssinstaller
    Post

    let`s take control of the SWAS

    If holding the dsc button for 30 seconds disables the sensor, why not just install a trigger module like the pac tr7 or tr12 to do it for you...
    Post by: Ssinstaller, Sep 13, 2020 in forum: Mazdaspeed 3 General Discussion
  9. Ssinstaller
    Post

    P2138, won’t rev above 3000 rpms, lots of smoke

    Ground wire at the hpfp bracket?
    Post by: Ssinstaller, Jun 14, 2020 in forum: Mazdaspeed 3/6 Engine
  10. Ssinstaller
    Post

    P2138, won’t rev above 3000 rpms, lots of smoke

    If there is ground with it plugged in, check the impedance between the two pins. If it's high that will cause issues as well.
    Post by: Ssinstaller, Jun 8, 2020 in forum: Mazdaspeed 3/6 Engine
  11. Ssinstaller
    Post

    P2138, won’t rev above 3000 rpms, lots of smoke

    What is the impedance betwen pin b at the pedal and pin 2h at the pcm? If the pcm is plugged in you should have continuity to ground on pin B, if...
    Post by: Ssinstaller, Jun 8, 2020 in forum: Mazdaspeed 3/6 Engine
  12. Ssinstaller
    Post

    Misfiring cyl 4

    IIRC the CR was 9.5 just like the ms6/ms3, only the turbo was slightly smaller.
    Post by: Ssinstaller, Jun 1, 2020 in forum: Mazdaspeed 3/6 Engine
  13. Ssinstaller
    Post

    Boosting in 6th Bad?

    Imo, if you're in 6th and boosting and your not going 120+MPH you're in the wrong gear. Downshift to pass.
    Post by: Ssinstaller, May 25, 2020 in forum: New Member Question and Answer Section
  14. Ssinstaller
    Post

    Random lock help

    Most modern cars wont let you lock from an interior switch with the drivers door open, so you can lock your keys in it. Except ford, they don't...
    Post by: Ssinstaller, May 25, 2020 in forum: Mazdaspeed 6 Troubleshooting
  15. Ssinstaller
    Post

    Random lock help

    Keyless fob isn't difficult to program.
    Post by: Ssinstaller, May 23, 2020 in forum: Mazdaspeed 6 Troubleshooting