Search Results

Search Again
Page 1 of 2
  1. ms6mil
    Thread

    Prothane Rear Sway Bar Bushings/Brackets

    This info was gathered back in 2013. It came time to swap out a busted stock axle for a DSS one. In the process, I encountered a couple issues...
    Thread by: ms6mil, Sep 7, 2016, 1 replies, in forum: Mazdaspeed 6 Suspension & Brakes
  2. ms6mil
    Post

    Amazon Tuned

    I looked up the free downloadable tunes and they don't have one that will match my mods. I think it's easier to just get a map for the time being...
    Post by: ms6mil, Aug 22, 2016 in forum: Mazdaspeed 3/6 ECU Tuning
  3. ms6mil
    Post

    Amazon Tuned

    But if I use my Prime account I will get a discount with the points I've earned. It would be even cheaper. I just need to be able to drive to...
    Post by: ms6mil, Aug 22, 2016 in forum: Mazdaspeed 3/6 ECU Tuning
  4. ms6mil
    Thread

    Amazon Tuned

    I was wondering if it would be safe to get a tune from HERE with my mods until I can afford a custom one. It's cheap and just need something to...
    Thread by: ms6mil, Aug 22, 2016, 38 replies, in forum: Mazdaspeed 3/6 ECU Tuning
  5. ms6mil
    Post

    OVER! VersaTuner Group Buy $100 off-Success!

    Email sent, I'm in.
    Post by: ms6mil, Aug 18, 2016 in forum: VersaTune
  6. ms6mil
    Post

    6th Port info needed (RE: SP63 Secondary kit)

    Appreciate it... So far so good for the wiring and placement of everything. I went ahead and purchased the parts necessary to replace the HPFP...
    Post by: ms6mil, May 11, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  7. ms6mil
    Post

    6th Port info needed (RE: SP63 Secondary kit)

    I have, for 130 bucks I could have gone for it but since I already have done the wiretuck, the solder work is easy to do and I won't have a bunch...
    Post by: ms6mil, May 5, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  8. ms6mil
    Post

    ms6mil's 5862 build, motor by EBTEC

    Motor is getting built, bsd, everything is aftermarket, not sure why #3 would run the hotest. I took a look at Clints thread on msf, # 3 seems to...
    Post by: ms6mil, Mar 11, 2016 in forum: Mazdaspeed 6 Build Diaries
  9. ms6mil
    Post

    ms6mil's 5862 build, motor by EBTEC

    Injector Rx has finished the cleaning.. results below. @Enki What is the norm? Spray pattern is "fair" should I use my other injectors, will...
    Post by: ms6mil, Mar 10, 2016 in forum: Mazdaspeed 6 Build Diaries
  10. ms6mil
    Post

    Forum Names Revealed

    Rob Moreno
    Post by: ms6mil, Mar 6, 2016 in forum: New Member Introduction Section
  11. ms6mil
    Post

    2015 ENM/MDC 1 Photos. Post em up here.

    [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: ms6mil, Mar 4, 2016 in forum: Dragon Camp Event Discussion
  12. ms6mil
    Thread

    6th Port info needed (RE: SP63 Secondary kit)

    Hey there, As part of my upcoming build, due to previously purchased parts, I went with the Kozmic kit. I've noticed after staring at the images...
    Thread by: ms6mil, Mar 3, 2016, 4 replies, in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  13. ms6mil
    Post

    ms6mil Dual Nozzle Meth Install w/ Throttle spacer

    No worries... just being as thorough as I can be... I have been asked that several times... :)
    Post by: ms6mil, Feb 29, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  14. ms6mil
    Post

    ms6mil Dual Nozzle Meth Install w/ Throttle spacer

    Had this discussion with the same thread in the other forum.... I used a sump and baffled 2.25 gal tank. I spoke with several people that have...
    Post by: ms6mil, Feb 29, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  15. ms6mil
    Post

    JgamB's "build it before you blow it" thread

    Made it home safely... as did the extra motor. Struggled uphill.. but all good. Thanks to everyone for having me over.
    Post by: ms6mil, Feb 28, 2016 in forum: Mazdaspeed 3 Build Diaries
  16. ms6mil
    Post

    JgamB's "build it before you blow it" thread

    easy peazy!!! see you Friday! [IMG]
    Post by: ms6mil, Feb 22, 2016 in forum: Mazdaspeed 3 Build Diaries
  17. ms6mil
    Post

    Engine Bay Photo Thread

    Before... [IMG] After... heart transplant TBD [IMG]
    Post by: ms6mil, Feb 22, 2016 in forum: Mazdaspeed 3/6 Appearance
  18. ms6mil
    Post

    JgamB's "build it before you blow it" thread

    Yup you got it...
    Post by: ms6mil, Feb 21, 2016 in forum: Mazdaspeed 3 Build Diaries
  19. ms6mil
    Post

    ms6mil's 5862 build, motor by EBTEC

    yeah... I'm in no rush... I talked to Chris a couple days ago and said it had just come back from the machine shop. I have another car as well...
    Post by: ms6mil, Feb 21, 2016 in forum: Mazdaspeed 6 Build Diaries
  20. ms6mil
    Thread

    ms6mil's 5862 build, motor by EBTEC

    Continued..... January 19 2016, Cleaned up the engine bay a little bit... unfortunately the car started running a little rough. [IMG] So.... I...
    Thread by: ms6mil, Feb 21, 2016, 8 replies, in forum: Mazdaspeed 6 Build Diaries
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2