4" Intake MAF Housing

Discussion in 'Mazdaspeed 3/6 Hard Parts Fabrication' started by Slow6_pl, Sep 2, 2016.

Watchers:
3 users.
  1. Slow6_pl

    Slow6_pl Greenie Member

    Joined:
    Feb 10, 2016
    Posts:
    106
    Trophy Points:
    28
    Location:
    Conway, AR
    Ratings:
    +57 / -1
    Thinking of fab bit up my own intake for my 5858 project. It will be topmounted, so essentially I just need to get around the engine, since my battery will more likely than not be in the trunk. However, I'm having a hard time finding a 4" MAF housing prefabbed. If I was to go with a pipe with my own MAF housing welded on, which housing is correct? Denso? Bosch? I saw a prefabbed Subaru (Denso) one that looked like ours, except the sensor # on ours wasn't listed. Thanks for any input, I'd rather do this right the first time!
     
    Slow6_pl, via a Samsung mobile device, Sep 2, 2016
    #1
  2. Enki

    Enki Motorhead Platinum Member

    Joined:
    Feb 10, 2016
    Posts:
    2,301
    Trophy Points:
    113
    Location:
    Tucson
    Ratings:
    +3,309 / -3
    Treadstone has what you need.
     
    Enki, Sep 2, 2016
    #2
    • Like Like x 1
  3. Slow6_pl

    Slow6_pl Greenie Member

    Joined:
    Feb 10, 2016
    Posts:
    106
    Trophy Points:
    28
    Location:
    Conway, AR
    Ratings:
    +57 / -1
    As usual, you're right. Dropping knowledge on all my posts.
     
    Slow6_pl, via a Samsung mobile device, Sep 2, 2016
    #3
  4. KiwiFlavor

    KiwiFlavor Greenie N00B Member

    Joined:
    Feb 11, 2016
    Posts:
    1,107
    Trophy Points:
    113
    Location:
    Somersworth, NH
    Ratings:
    +1,479 / -11
    :enki:
     
    KiwiFlavor, Sep 2, 2016
    #4
    • Like Like x 3
  5. Enki

    Enki Motorhead Platinum Member

    Joined:
    Feb 10, 2016
    Posts:
    2,301
    Trophy Points:
    113
    Location:
    Tucson
    Ratings:
    +3,309 / -3
    It's not unusual for me to be wrong, too.
     
    Enki, Sep 2, 2016
    #5
    • Like Like x 1
Loading...
Similar Threads - Intake Housing
  1. Enki

    CS Intake mani - Port injection w/ TMIC

    Enki, Dec 31, 2023, in forum: Fueling Knowledgebase
    Replies:
    8
    Views:
    482
    RyGuyv
    Feb 14, 2024
  2. Enki

    Grams Per Second (AKA How to SUCC properly AKA MAF and intake thread AKA

    Enki, Dec 12, 2023, in forum: Tuning Knowledgebase
    Replies:
    0
    Views:
    305
    Enki
    Dec 12, 2023
  3. brbk

    Replaced the accordion tube on the stock intake with silicone

    brbk, Aug 23, 2023, in forum: SKYACTIV-2.5T How-To
    Replies:
    1
    Views:
    580
    brbk
    Aug 25, 2023
  4. DEname

    [SOLVED] Fuel inside intake manifold from tuning ?

    DEname, Aug 9, 2023, in forum: Mazdaspeed 3 Troubleshooting
    Replies:
    11
    Views:
    644
    DEname
    Oct 15, 2023
  5. SJones

    Alternative intake manifold

    SJones, Jul 16, 2023, in forum: Mazdaspeed 3/6 Engine
    Replies:
    8
    Views:
    340
    Easter Bunny
    Jul 17, 2023

Share This Page

Users Viewing Thread (Users: 0, Guests: 0)