Search Results

Search Again
Page 1 of 2
  1. Boost_creep
    Post

    A discussion on mitigating engine bay heat

    I've been removing and installing my undertray to do engine work, for the past 6 years! My Gen1 uses 3 10mm bolts across the front and then 2 on...
    Post by: Boost_creep, May 11, 2016 in forum: Mazdaspeed 3/6 Engine
  2. Boost_creep
    Post

    VVT replacement

    Do you say that because you're confident it will fail? Lol.
    Post by: Boost_creep, Apr 27, 2016 in forum: Mazdaspeed 3 General Discussion
  3. Boost_creep
    Thread

    VVT replacement

    Hey guys. I've owned my Gen 1 since 2010 and 16k miles. I now have 93k, and have yet to ever do any vvt work. It has never made any noise, so I...
    Thread by: Boost_creep, Apr 27, 2016, 4 replies, in forum: Mazdaspeed 3 General Discussion
  4. Boost_creep
    Post

    Installed Snow Meth Kit + bracket to hold my corn juice

    Good to know!
    Post by: Boost_creep, Apr 15, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  5. Boost_creep
    Post

    Installed Snow Meth Kit + bracket to hold my corn juice

    Yes, I agree. I think the pump pressure may actually damage the SafeInjection unit, so I hope the OP reads this in time.
    Post by: Boost_creep, Mar 29, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  6. Boost_creep
    Post

    Installed Snow Meth Kit + bracket to hold my corn juice

    Hmm. Very interesting. The directions I have are from 2014, and they state the SafeInjection should be between the tank and pump.
    Post by: Boost_creep, Mar 29, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  7. Boost_creep
    Post

    Installed Snow Meth Kit + bracket to hold my corn juice

    Yea, don't worry about following the directions. Those are overrated too.
    Post by: Boost_creep, Mar 29, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  8. Boost_creep
    Post

    Installed Snow Meth Kit + bracket to hold my corn juice

    Isn't the SafeInjection supposed to be between the tank and pump?
    Post by: Boost_creep, Mar 28, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  9. Boost_creep
    Post

    John's BNR S3 daily driver performance build

    See tech tip below. But as long as spray pattern is not obstructed, you should be fine. [ATTACH]
    Post by: Boost_creep, Mar 3, 2016 in forum: Mazdaspeed 3 Build Diaries
  10. Boost_creep
    Post

    John's BNR S3 daily driver performance build

    I would bring that nozzle in a touch more. The outer edge should be flush with the inside wall and the nozzle tip should actually be slightly...
    Post by: Boost_creep, Mar 1, 2016 in forum: Mazdaspeed 3 Build Diaries
  11. Boost_creep
    Post

    Intercooler core discussion

    Well it's been like 20* ambient here in NY, so it's kinda hard to tell. Lol. Ect's have been normal at 183-187*. I'm really thinking of going for...
    Post by: Boost_creep, Feb 20, 2016 in forum: Mazdaspeed 3 General Discussion
  12. Boost_creep
    Post

    Intercooler core discussion

    Well, I am running the cpe mani now. Those pictures were taken 2 years ago when I tried going fmic. Do you think that will have an effect on temps...
    Post by: Boost_creep, Feb 20, 2016 in forum: Mazdaspeed 3 General Discussion
  13. Boost_creep
    Post

    Intercooler core discussion

    I saw that on Facebook recently, and thanks for bringing that up. I think it's a very good point, and leads me to another question. When I...
    Post by: Boost_creep, Feb 19, 2016 in forum: Mazdaspeed 3 General Discussion
  14. Boost_creep
    Post

    Intercooler core discussion

    I thought Justin was running the Cobb core? I am spraying a ton of meth too. Lol. So I'm not too concerned with wot bat's, but really more...
    Post by: Boost_creep, Feb 19, 2016 in forum: Mazdaspeed 3 General Discussion
  15. Boost_creep
    Post

    Intercooler core discussion

    Well, I'm not running the fmic kit anymore. I removed it due to heat issues. But this was my setup. [ATTACH] [ATTACH] [ATTACH]
    Post by: Boost_creep, Feb 19, 2016 in forum: Mazdaspeed 3 General Discussion
  16. Boost_creep
    Post

    Intercooler core discussion

    Maybe this is more pronounced on Gen1 :(
    Post by: Boost_creep, Feb 19, 2016 in forum: Mazdaspeed 3 General Discussion
  17. Boost_creep
    Post

    Intercooler core discussion

    I've actually been more keen on the 3" cores, because my thoughts were that the 3.5" thick TR8 that I had was butted up against my radiator. I'm...
    Post by: Boost_creep, Feb 19, 2016 in forum: Mazdaspeed 3 General Discussion
  18. Boost_creep
    Thread

    Intercooler core discussion

    I wanted to start a discussion to get people's opinions/observations on the different FMIC cores on the market. I am running a CP-E tmic at the...
    Thread by: Boost_creep, Feb 19, 2016, 20 replies, in forum: Mazdaspeed 3 General Discussion
  19. Boost_creep
    Thread

    CP-E Fuel Rail

    It looks like cp-e released the havoc fuel rail, for their manifold. Maybe we can use this thread to gather data, since I don't see them as being...
    Thread by: Boost_creep, Feb 11, 2016, 2 replies, in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  20. Boost_creep
    Post

    Neganox's Cats Can't Drive Build.

    I am also eagerly awaiting HTP's meth tank release. Sorry to derail for one quick sec, but your a moderator, so the best to ask. How do you quote...
    Post by: Boost_creep, Feb 11, 2016 in forum: Mazdaspeed 3 Build Diaries
Showing results 1 to 20 of 23 Next >
Search Again
Page 1 of 2