Ring gaps, keying and bearings

Discussion in 'Mazdaspeed 3/6 Engine' started by drew10101010, Dec 18, 2020.

Watchers:
7 users.
Page 2 of 2
  1. phate

    phate Motorhead

    Joined:
    Feb 10, 2016
    Posts:
    384
    Trophy Points:
    93
    Location:
    Westland, MI
    Ratings:
    +996 / -1
    No

    Sent from my SM-F916U using Tapatalk
     
    phate, via a mobile device, Dec 25, 2020
    #21
  2. drew10101010

    drew10101010 Greenie Member

    Joined:
    Oct 11, 2020
    Posts:
    117
    Trophy Points:
    28
    Location:
    Maryland
    Ratings:
    +76 / -3
    m.JPG
     
    Last edited: Jan 13, 2021
    drew10101010, Dec 25, 2020
    #22
  3. drew10101010

    drew10101010 Greenie Member

    Joined:
    Oct 11, 2020
    Posts:
    117
    Trophy Points:
    28
    Location:
    Maryland
    Ratings:
    +76 / -3
    So I just heard back from Freek and he cleared up alot of confusion for me and hopefully it can help others. freek.JPG
    freek3.JPG
    freek2.JPG
    Guess I'll just run oem bolts! Also good to know stocks sleeves can handle 700+.
     
    drew10101010, Jan 13, 2021
    #23
  4. anthony

    anthony Greenie Member

    Joined:
    Apr 28, 2016
    Posts:
    180
    Trophy Points:
    43
    Location:
    az
    Ratings:
    +166 / -2
    I say go l19s or freeks h11s for future proof its definitely worth the investment
     
    anthony, Jan 13, 2021
    #24
  5. drew10101010

    drew10101010 Greenie Member

    Joined:
    Oct 11, 2020
    Posts:
    117
    Trophy Points:
    28
    Location:
    Maryland
    Ratings:
    +76 / -3
    I have Freek h11's :)
     
    drew10101010, Jan 13, 2021
    #25
    • Like Like x 1
  6. anthony

    anthony Greenie Member

    Joined:
    Apr 28, 2016
    Posts:
    180
    Trophy Points:
    43
    Location:
    az
    Ratings:
    +166 / -2
    oh my bad read that completely wrong you were talking about the OEM CRANK bolt my bad
     
    anthony, Jan 14, 2021
    #26
    • Like Like x 1
  7. javen Broadnax

    javen Broadnax Greenie N00B Member

    Joined:
    May 9, 2024
    Posts:
    4
    Trophy Points:
    1
    Location:
    North Carolina
    Ratings:
    +0 / -0
    Did you have any problems running 0.21top ring 0.24
     
    javen Broadnax, via an iPhone, May 9, 2024
    #27
  8. drew10101010

    drew10101010 Greenie Member

    Joined:
    Oct 11, 2020
    Posts:
    117
    Trophy Points:
    28
    Location:
    Maryland
    Ratings:
    +76 / -3
    I haven't used the built engine yet. Short block is done and has been sitting in my garage for a while now. I'm on a JDM cx-7 and it's running mint. But that gap is perfect. Justin confirmed it and it was confirmed here in other threads. Manley's recommendation is way too loose.
     
    drew10101010, May 14, 2024
    #28
Page 2 of 2
Loading...
Similar Threads - Ring gaps keying
  1. javen Broadnax

    Question about built motor ring gaps

    javen Broadnax, May 10, 2024, in forum: Mazdaspeed 3/6 Engine
    Replies:
    2
    Views:
    707
    javen Broadnax
    May 10, 2024
  2. Twoodsy

    Intermittent loss of power steering

    Twoodsy, Apr 22, 2025, in forum: Mazdaspeed 3 Troubleshooting
    Replies:
    3
    Views:
    175
    kgyawa26
    Apr 23, 2025
  3. Seal

    Steering wheel lock

    Seal, Apr 18, 2025, in forum: Mazdaspeed 3 General Discussion
    Replies:
    16
    Views:
    395
    Seal
    Apr 25, 2025
  4. philip B

    B12 Oil Control Rings soak ?

    philip B, Apr 14, 2025, in forum: New Member Question and Answer Section
    Replies:
    33
    Views:
    1,126
    Crazycanadian
    May 3, 2025
  5. Matt@DM

    Injector Stud Kit, and Injector O-ring kit

    Matt@DM, Mar 27, 2025, in forum: Damond Motorsports
    Replies:
    13
    Views:
    401
    Matt@DM
    Apr 2, 2025

Share This Page

Users Viewing Thread (Users: 0, Guests: 1)