Recent Content by Gegi

  1. Gegi
    Post

    Aux Fuel Confusion

    Hi! The stock intake has a lot of imbalance between the runners, so each cylinder will receive different amount of extra fueling. I think you...
    Post by: Gegi, Jun 1, 2022 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  2. Gegi
    Post

    Gauge pod

    I did. Terrible fit, had to trim and glue it to place. Also very bad finish, I'm not recommending it.. Tapatalkkal küldve az én KB2003 eszközömről
    Post by: Gegi, Oct 30, 2021 in forum: Mazdaspeed 6 General Discussion
  3. Gegi
    Post

    14.85 AFR, fuel trims pinned at -.16, knock retard?!

    If your AFR is stuck at 14.85 you have a bad primary o2 sensor. It is the most important sensor in your car, change it as soon as possible. Also...
    Post by: Gegi, Aug 29, 2021 in forum: Mazdaspeed 3 Troubleshooting
  4. Gegi
    Post

    Wire Fuel Pump - Hellcat 525LPH or any Big LPFP

    Thank you very much for the help, I appreciate it!
    Post by: Gegi, May 11, 2021 in forum: Mazdaspeed 3 How-To
  5. Gegi
    Post

    Wire Fuel Pump - Hellcat 525LPH or any Big LPFP

    Unfortunately I think I have. Any tips what to check for exactly? Sent from my KB2003 using Tapatalk
    Post by: Gegi, May 10, 2021 in forum: Mazdaspeed 3 How-To
  6. Gegi
    Post

    Wire Fuel Pump - Hellcat 525LPH or any Big LPFP

    Guys I really hope someone can help me out. I have a dw300c as my ifp, I have a speed6. Since that has been changed I can only use the gas in my...
    Post by: Gegi, May 10, 2021 in forum: Mazdaspeed 3 How-To
  7. Gegi
    Post

    New 4” intake

    I live in Hungary so I think it is not an option :) Also not planning to go smaller after this badboy. Sent from my ONEPLUS A5010 using Tapatalk
    Post by: Gegi, Oct 24, 2020 in forum: Corksport
  8. Gegi
    Post

    New 4” intake

    Yeah, I think so :) I was worried because CS said it will not work, but I said fuck it I'll make it work somehow. Also my engine was ready and no...
    Post by: Gegi, Oct 24, 2020 in forum: Corksport
  9. Gegi
    Post

    New 4” intake

    I had to remove the small bracket that holds the o2 sensor cables because the nipple at the bottom was hitting it and there was not enough...
    Post by: Gegi, Oct 24, 2020 in forum: Corksport
  10. Gegi
    Post

    New 4” intake

    Since 3.5" was not in stock I had to get this. Fits easily in my 6 with 51r battery. [ATTACH] [ATTACH]
    Post by: Gegi, Oct 24, 2020 in forum: Corksport
  11. Gegi
    Post

    3" or 3.5" intake for cst4?

    I have the CST4 with the CS3" intake on the stock fuel system. I'm around 4.12V on the MAF at WOT, so I think there's some room for more air. If...
    Post by: Gegi, Apr 29, 2020 in forum: Mazdaspeed 3 General Discussion
  12. Gegi
    Post

    What are these mods?

    The first one is the TB coolent bypass. That pipe is the same in mine and in others, I believe it is an overflow pipe.
    Post by: Gegi, Apr 11, 2020 in forum: Mazdaspeed 3/6 Engine