Recent Content by JohnnyTightlips

  1. JohnnyTightlips
    Post

    What coolant is best?

    https://www.walmart.com/ip/Valvoline-Zerex-Asian-RED-Vehicle-Antifreeze-Coolant-1-Gallon/49660461 This is what I have always used they should...
    Post by: JohnnyTightlips, Jun 15, 2021 at 10:14 AM in forum: Mazdaspeed 3/6 Engine
  2. JohnnyTightlips
    Thread

    [SOLVED] P0335 after new turbo and ex manifold

    I recently installed the Pulsar GTX3071r and the Corksport Exhaust Manifold. I kept getting P0335 code when I would start my car. I mentioned this...
    Thread by: JohnnyTightlips, Jun 14, 2021 at 4:03 PM, 0 replies, in forum: Mazdaspeed 3 Troubleshooting
  3. JohnnyTightlips
    Post

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    I updated the oil drain section on the main post.
    Post by: JohnnyTightlips, Jun 14, 2021 at 3:49 PM in forum: Mazdaspeed 3 How-To
  4. JohnnyTightlips
    Post

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    Car is on the road and the tuning has begun. Some more pictures of the setup. I will add the oil drain info to the main thread. here are a few...
    Post by: JohnnyTightlips, Jun 14, 2021 at 3:30 PM in forum: Mazdaspeed 3 How-To
  5. JohnnyTightlips
    Post

    StreetSpeed’s DD 500+ MS6 Build

    I use this wire and it is very nice, 2 awg pure copper. 2 awg OFC is more like 6 awg copper so maybe it is not doing the job and putting stress on...
    Post by: JohnnyTightlips, Jun 11, 2021 at 10:06 AM in forum: Mazdaspeed 6 Build Diaries
  6. JohnnyTightlips
    Post

    Frick Remans - Going Built

    That's great to hear. Always nice when people care about helping you and know their stuff.
    Post by: JohnnyTightlips, Jun 9, 2021 in forum: Mazdaspeed 3 Build Diaries
  7. JohnnyTightlips
    Post

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    $669.99 "nice" and if you spend more you can get the T51R mod lol [ATTACH]
    Post by: JohnnyTightlips, Jun 8, 2021 in forum: Mazdaspeed 3 How-To
  8. JohnnyTightlips
    Post

    GB Remanufacturing (Rock Auto) fuel injector rebuild kit

    My car runs pretty rough on cold starts if I try and hoon at all. I am sure it is tune related and the JMF with no vtcs. As soon as it gets over...
    Post by: JohnnyTightlips, Jun 8, 2021 in forum: Mazdaspeeds.org Official Parts Reviews Section
  9. JohnnyTightlips
    Post

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    Both, the Pulsar turbos have been pretty consistent and well reviewed on youtube etc. I am hoping to get more midrange , not looking for any more...
    Post by: JohnnyTightlips, Jun 7, 2021 in forum: Mazdaspeed 3 How-To
  10. JohnnyTightlips
    Post

    JohnnyTightlips Build "Maximum Carnage"

    Truth
    Post by: JohnnyTightlips, Jun 7, 2021 in forum: Mazdaspeed 3 Build Diaries
  11. JohnnyTightlips
    Post

    JohnnyTightlips Build "Maximum Carnage"

    Update I went to rebuild my PTE turbo and only found sadness. It still ran 1+ years this way and made 600 ish whp so it done good. I believe when...
    Post by: JohnnyTightlips, Jun 7, 2021 in forum: Mazdaspeed 3 Build Diaries
  12. JohnnyTightlips
    Post

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    Thanks, Fixed
    Post by: JohnnyTightlips, Jun 7, 2021 in forum: Mazdaspeed 3 How-To
  13. JohnnyTightlips
    Thread

    Ebay Pulsar GTX3071R CS - CorkSport Manifold- Install and Impressions

    I had the opportunity to get a CS manifold and after talking to @CorkSport - Derrick he mentioned that they were testing out a Tial v-band flange...
    Thread by: JohnnyTightlips, Jun 7, 2021, 9 replies, in forum: Mazdaspeed 3 How-To