Recent Content by Torquemaniac

  1. Torquemaniac
    Post

    Ozy built CX7

    Hey Ozy...wheres the rest of the thread...you cant post a pic of your car and call it a day :P
    Post by: Torquemaniac, Jan 31, 2017 in forum: CX-7 Build Diaries
  2. Torquemaniac
    Thread

    MAZDA dealer extranet access

    Found this link while searching on the net : http://am.mazdaserviceinfo.com/mazdaesi/index?page=login I just registered by clicking on the...
    Thread by: Torquemaniac, Jan 25, 2017, 9 replies, in forum: Mazdaspeed 3 General Discussion
  3. Torquemaniac
    Post

    Torq's big turbo build part II

    LOL...give me some more cash and free time and I will make this 500hp build a thing of the past Right now its freakin cold here (-20C this...
    Post by: Torquemaniac, Jan 9, 2017 in forum: CX-7 Build Diaries
  4. Torquemaniac
    Post

    Lets talk about turbo blankets/heat wrap

    I was in the same boat...liked the exhaust tone of my setup, but wanted less drone in the cabin...I insulated pretty much all the hatch area...
    Post by: Torquemaniac, Jan 3, 2017 in forum: Mazdaspeed 3/6 Engine
  5. Torquemaniac
    Post

    Lets talk about turbo blankets/heat wrap

    A J-pipe helped a lot for my cruising drone...I have a calculator sheet if you want to measure the J-pipe needed on your setup Pics of my exhaust...
    Post by: Torquemaniac, Jan 2, 2017 in forum: Mazdaspeed 3/6 Engine
  6. Torquemaniac
    Post

    Mastermind's Build

    Humm...anyway you should not run VTA unless youre MAF is after the BPV (blow-thru setup)!
    Post by: Torquemaniac, Dec 29, 2016 in forum: Mazdaspeed 3 Build Diaries
  7. Torquemaniac
    Post

    Mastermind's Build

    Funny...mine blowing air at idle (maybe turbo size makes a difference...I have a Holset HY35)
    Post by: Torquemaniac, Dec 28, 2016 in forum: Mazdaspeed 3 Build Diaries
  8. Torquemaniac
    Post

    Mastermind's Build

    FYI, I am running the Forge V2 in VTA with no problem...but my MAF is after the Forge (right before the throttle body)
    Post by: Torquemaniac, Dec 28, 2016 in forum: Mazdaspeed 3 Build Diaries
  9. Torquemaniac
    Post

    Lets talk about turbo blankets/heat wrap

    I used Resbond 907 ceramic adhesive : http://www.cotronics.com/catalog/30%20%207030%20%20907.pdf When heat cured at 350-450F (I used the BBQ),...
    Post by: Torquemaniac, Dec 26, 2016 in forum: Mazdaspeed 3/6 Engine
  10. Torquemaniac
    Post

    Lets talk about turbo blankets/heat wrap

    I have a cheap CXracing T3 blanket over my Holset, and it work just fine (prevent stuff around the turbo from burning or melting) Only downside...
    Post by: Torquemaniac, Dec 22, 2016 in forum: Mazdaspeed 3/6 Engine
  11. Torquemaniac
    Post

    HPFP O-rings

    Its the X-ring indeed...this one https://www.mcmaster.com/#6540k121/=x086r6 I got the metric one ( https://www.mcmaster.com/#1200n156/=14k9f5x )...
    Post by: Torquemaniac, Dec 5, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  12. Torquemaniac
    Post

    HPFP O-rings

    Just put the McMaster-Carr dash 011 o-ring in my HPFP today (with some fresh Rotella T6)..did a test drive tonight and the air coming out of the...
    Post by: Torquemaniac, Nov 26, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  13. Torquemaniac
    Post

    Torq's big turbo build part II

    Now on to part II When I first monitored high crankcase pressure (7+psi), I thought that the opened up ring gap (0.014 first ring, 0.019 second...
    Post by: Torquemaniac, Feb 21, 2016 in forum: CX-7 Build Diaries
  14. Torquemaniac
    Post

    Torq's big turbo build part II

    [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG] [IMG]...
    Post by: Torquemaniac, Feb 21, 2016 in forum: CX-7 Build Diaries