Recent Content by JT020110

  1. JT020110
    Post

    How-to: MS6 Seat Swap to Gen1 Seats (MSjuan6 Seats)

    Thanks!!
    Post by: JT020110, Aug 2, 2023 in forum: Mazdaspeed 6 How-To
  2. JT020110
    Thread

    How-to: MS6 Seat Swap to Gen1 Seats (MSjuan6 Seats)

    My first how to, been years since I have posted anything this long on a forum lol. Anywho. This is a hopefully a simple how to with lots of...
    Thread by: JT020110, Aug 2, 2023, 6 replies, in forum: Mazdaspeed 6 How-To
  3. JT020110
    Post

    Best Cheap Mods

    Reys Mazda Parts on FB sells HPFP rebuild kit for like 35 bucks, the X-ring inside helps prevent fuel dilution in your oil.
    Post by: JT020110, Nov 23, 2020 in forum: New Member Question and Answer Section
  4. JT020110
    Post

    Custom Shift Cable

    If i had a welder I would have used the exact design above, its nice and simple. Since i don't have a welder I have used 2'' square metal tubing...
    Post by: JT020110, Apr 17, 2020 in forum: Mazdaspeed 6 Transmission/Drivetrain
  5. JT020110
    Post

    The ButtStallion Build

    Excited to see the results!
    Post by: JT020110, Nov 1, 2017 in forum: Mazdaspeed 3 Build Diaries
  6. JT020110
    Post

    Disi-MZResponse

    very nice man
    Post by: JT020110, Aug 21, 2016 in forum: Mazdaspeed 3 Build Diaries
  7. JT020110
    Post

    Let's see those alternate paint schemes

    What spoiler is that bud - looks amazing
    Post by: JT020110, May 3, 2016 in forum: Mazdaspeed 3/6 Appearance
  8. JT020110
    Post

    MS6 Devils own install in bumper w/ FMIC

    good to know from what I read I thought that the pump lines just needed to be as close as level or below bulkhead. I wonder if I can drop it down...
    Post by: JT020110, Apr 19, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  9. JT020110
    Post

    MS6 Devils own install in bumper w/ FMIC

    thanks I like those are nice and would make the lines shorter too - I left quite a bit there so it wouldn't pull the connection points but just...
    Post by: JT020110, Apr 17, 2016 in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  10. JT020110
    Thread

    MS6 Devils own install in bumper w/ FMIC

    So I was messing around with the idea of using the oem tank for meth but house it on the drivers side. And it actually fits as well as the pump....
    Thread by: JT020110, Apr 17, 2016, 5 replies, in forum: Mazdaspeed 3/6 Fuel, NOS, Meth, & Water Injection
  11. JT020110
    Thread

    MS6 10'' sealed box install

    So I finished this setup last week, just wanted to share. made out of 3/4'' MDF board Kicker 600.1 Kicker 250.4 JL 10w1v2 Dimensions for .52XX...
    Thread by: JT020110, Apr 7, 2016, 1 replies, in forum: Mazdaspeed 3/6 Audio & Electronics
  12. JT020110
    Post

    Navy's MS6 Bumper Fix How-To

    Very nice! I dug up a few of my pictures when I did mine, only difference is I put mine more forward, used the existing pin holes that line up the...
    Post by: JT020110, Mar 15, 2016 in forum: RaiderFab Bumper Fitment Solutions LLC